CAD (0) ▾
  • Cart is empty
  1. Request CAD files
TDI bearings have a one-piece double inner race and two single outer races and are typically supplied complete with an outer race spacer as a pre-set assembly. The bearing can be used at fixed positions on rotation shaft applications. For rotating housing application it can be used to float on the stationary shaft.
Request Information
Unit of Measure

Specifications

Series

 N/A 81000

Cone Part Number

 N/A 81601D

Cup Part Number

 N/A 81964

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Note

 N/A This part has a non-standard shoulder design. Please email customer CAD for shoulder details to ensure the proper design of mating components.

Dimensions

d - Bore

 N/A 6 in152.400 mm

D - Cup Outer Diameter

 N/A 9.6457 in245.001 mm

B - Double Cone Width

 N/A 3.6250 in92.075 mm

C - Cup Width

 N/A 1.3125 in33.338 mm

T - Bearing Width across Cups

 N/A 3.4375 in87.313 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.06 in1.5 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 6.54 in166.1 mm

Db - Cup Backface Backing Diameter

 N/A 8.86 in225.04 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.03 in0.8 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (One-Row, 90 million revolutions)3 N/A 23400 lbf104000 N
C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)4 N/A 157000 lbf699000 N
C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)5 N/A 40800 lbf181000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 14100 lbf62700 N

Factors

K - Factor7 N/A 1.66
e - ISO Factor8 N/A 0.35
Y1 - ISO Factor9 N/A 1.92
Y2 - ISO Factor10 N/A 2.86

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 413

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 98.4
Cg - Geometry Factor11 N/A 0.125

Spacer

Note

 N/A Spacer shows standard nominal .01 radii, actual bearing may vary
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 4 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 5 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 11 Geometry constant for Lubrication Life Adjustment Factor a3l.