CAD (0) ▾
  • Cart is empty
  1. Request CAD files
TDI bearings have a one-piece double inner race and two single outer races and are typically supplied complete with an outer race spacer as a pre-set assembly. The bearing can be used at fixed positions on rotation shaft applications. For rotating housing application it can be used to float on the stationary shaft.
Request Information
Unit of Measure

Specifications

Series

 N/A 82600

Cone Part Number

 N/A 82680D

Cup Part Number

 N/A 82622

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 7 in177.800 mm

D - Cup Outer Diameter

 N/A 10.7500 in273.050 mm

B - Double Cone Width

 N/A 4.4375 in112.713 mm

C - Cup Width

 N/A 1.7187 in43.655 mm

T - Bearing Width across Cups

 N/A 4.4373 in112.707 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.06 in1.5 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 7.76 in197 mm

Db - Cup Backface Backing Diameter

 N/A 9.80 in248.92 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.06 in1.5 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (One-Row, 90 million revolutions)3 N/A 31100 lbf138000 N
C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)4 N/A 209000 lbf930000 N
C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)5 N/A 54200 lbf241000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 28000 lbf124000 N

Factors

K - Factor7 N/A 1.11
e - ISO Factor8 N/A 0.52
Y1 - ISO Factor9 N/A 1.29
Y2 - ISO Factor10 N/A 1.92

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 661

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 119
Cg - Geometry Factor11 N/A 0.131

Spacer

Note

 N/A Spacer shows standard nominal .01 radii, actual bearing may vary
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 4 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 5 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 11 Geometry constant for Lubrication Life Adjustment Factor a3l.