CAD (0) ▾
  • Cart is empty
  1. Request CAD files
TDI bearings have a one-piece double inner race and two single outer races and are typically supplied complete with an outer race spacer as a pre-set assembly. The bearing can be used at fixed positions on rotation shaft applications. For rotating housing application it can be used to float on the stationary shaft.
Request Information
Unit of Measure

Specifications

Series

 N/A 132000

Cone Part Number

 N/A EE132081D

Cup Part Number

 N/A 132125

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A EE132081D-90045 EE132081D-902A1

Dimensions

d - Bore

 N/A 8 in203.2 mm

D - Cup Outer Diameter

 N/A 12.5000 in317.500 mm

B - Double Cone Width

 N/A 3.7500 in95.250 mm

C - Cup Width

 N/A 1.3750 in34.925 mm

T - Bearing Width across Cups

 N/A 3.7500 in95.250 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.13 in3.300 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 8.82 in224 mm

Db - Cup Backface Backing Diameter

 N/A 11.57 in293.88 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.17 in4.3 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (One-Row, 90 million revolutions)3 N/A 30800 lbf137000 N
C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)4 N/A 207000 lbf919000 N
C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)5 N/A 53600 lbf238000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 16500 lbf73400 N

Factors

K - Factor7 N/A 1.86
e - ISO Factor8 N/A 0.31
Y1 - ISO Factor9 N/A 2.15
Y2 - ISO Factor10 N/A 3.21
Cg - Geometry Factor11 N/A 0.117

Spacer

Note

 N/A Spacer shows standard nominal .01 radii, actual bearing may vary
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 4 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 5 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 11 Geometry constant for Lubrication Life Adjustment Factor a3l.