CAD (0) ▾
  • Cart is empty
  1. Request CAD files
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Request Information
Unit of Measure

Specifications

Series

 N/A HM133400

Cone Part Number

 N/A JHM133449

Cup Part Number

 N/A JHM133417

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 160 mm6.2992 in

D - Cup Outer Diameter

 N/A 255 mm10.0394 in

B - Cone Width

 N/A 69.850 mm2.7500 in

C - Cup Width

 N/A 52.388 mm2.0625 in

T - Bearing Width

 N/A 63.500 mm2.5000 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 1.520 mm0.06 in
r - Cup Backface "To Clear" Radius2 N/A 3.30 mm0.130 in

da - Cone Frontface Backing Diameter

 N/A 173 mm6.81 in

db - Cone Backface Backing Diameter

 N/A 173 mm6.81 in

Da - Cup Frontface Backing Diameter

 N/A 233.93 mm9.21 in

Db - Cup Backface Backing Diameter

 N/A 230.89 mm9.09 in

Ab - Cage-Cone Frontface Clearance

 N/A 1.8 mm0.07 in

Aa - Cage-Cone Backface Clearance

 N/A 1.5 mm0.06 in
a - Effective Center Location3 N/A -17.3 mm-0.68 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 165000 N37000 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 635000 N143000 lbf

C0 - Static Radial Rating

 N/A 1040000 N233000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 74600 N16800 lbf

Factors

K - Factor7 N/A 2.21
e - ISO Factor8 N/A 0.26
Y - ISO Factor9 N/A 2.27

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 668.6

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 103.2
Cg - Geometry Factor10 N/A 0.134
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.